SK6812

Sk6812-Free PDF

  • Date:11 Apr 2020
  • Views:49
  • Downloads:0
  • Pages:12
  • Size:555.31 KB

Share Pdf : Sk6812

Download and Preview : Sk6812


Report CopyRight/DMCA Form For : Sk6812


Transcription:

Technical Data Sheet,INTEGRATED LIGHT SOURCE INTELLIGENT CONTROL. OF CHIP ON TOP SMD TYPE LED,Model SK6812,1 Product Overview. SK6812 is a smart LED control circuit and light emitting circuit in one controlled LED source which. has the shape of a 5050 LED chip Each lighting element is a pixel and the intensities of the pixels are. contained within the intelligent digital interface input The output is driven by patented PWM. technology which effectively guarantees high consistency of the color of the pixels The control. circuit consists of a signal shaping amplification circuit a built in constant current circuit and a high. precision RC oscillator, The data protocol being used is unipolar NRZ communication mode The 24 bit data is transmitted. from the controller to DIN of the first element and if it is accepted it is extracted pixel to pixel After an. internal data latch the remaining data is passed through the internal amplification circuit and sent out. on the DO port to the remaining pixels The pixel is reset after the end of DIN Using automatic. shaping forwarding technology makes the number of cascaded pixels without signal transmission only. limited by signal transmission speed, The LED has a low driving voltage which allows for environmental protection and energy saving. high brightness scattering angle good consistency low power and long life The control circuit is. integrated in the LED above,2 Main Application Field.
Full color LED string light LED full color module LED super hard and soft lights LED guardrail tube. LED appearance scene lighting, LED point light LED pixel screen LED shaped screen a variety of electronic products electrical. equipment etc,3 Description, Top SMD internal integrated high quality external control line serial cascade constant current IC. control circuit and the RGB chip in SMD 5050 components to form a complete control of pixel color. mixing uniformity and consistency, built in data shaping circuit a pixel signal is received after wave shaping and output waveform. distortion will not guarantee a line, The built in power on reset and reset circuit the power does not work. gray level adjusting circuit 256 level gray scale adjustable. red drive special treatment color balance,line data transmission.
plastic forward strengthening technology the transmission distance between two points over 10M. Using a typical data transmission frequency of 800 Kbps when the refresh rate of 30 frames per sec. 2 12 Document No SPC SK6812 Rev No 03,www szledcolor com. Technical Data Sheet,4 Mechanical Dimensions,1 All dimensions are in millimeters. 2 Tolerance is 0 1mm unless otherwise noted,5 PIN configuration. NO Symbol Function description,1 VDD Power supply LED. 2 DOUT Control data signal output,3 VSS Ground,4 DIN Control data signal input.
6 General Information, SK6812 The default is RGB chips with IC integration. 3 12 Document No SPC SK6812 Rev No 03,www szledcolor com. Technical Data Sheet,7 Absolute Maximum Ratings Ta 25 VSS 0V. Parameter Symbol Range Unit,Power supply voltage VDD 3 5 5 5 V. Logic input voltage VIN 0 5 VDD 0 5 V,Working temperature Topt 40 85.
Storage temperature Tstg 50 150,ESD pressure VESD 4K V. 8 The electrical parameters unless otherwise specified TA 20 70 VDD 4 5 5 5V. Parmeter Symbol Min Typical Max Unit Test conditions. supply voltage,R G B port VDS M,pressure AX,DOUT conect ground. IDOH 49 mA the maximum drive,DOUT drive current,capability. DOUT conect the,IDOL 50 mA,largest current,The signal VIH 3 4 V. input flip VDD 5 0V,threshold VIL 1 6 V,The frequency.
FPWM 1 2 KHZ,Static power,consumption,9 The dynamic parameters Ta 25. Parameter Symbol Min Typical Max Unit Test conditions. The speed of data The duty ratio of 67,fDIN 800 KHZ. transmission data 1,DOUT transmission TPLH 500 ns,delay TPHL 500 ns. IOUT Rise Drop Tr 100 ns VDS 1 5,Time Tf 100 ns IOUT 13mA. 4 12 Document No SPC SK6812 Rev No 03,www szledcolor com.
Technical Data Sheet,10 The data transmission time TH TL 1 25 s 600ns. T0H 0 code high level time 0 3 s 0 15 s,T0L 0 code low level time 0 9 s 0 15 s. T1H 1 code high level time 0 6 s 0 15 s,T1L 1 code low level time 0 6 s 0 15 s. Trst Reset code low level time 80 s,11 Timing waveform. Input code Connection mode,D1 D2 D3 D4,DIN DO DIN DO DIN DO.
PIX1 PIX2 PIX3,12 The method of data transmission, Note the D1 sends data for MCU D2 D3 D4 for data forwarding automatic shaping cascade circuit. 5 12 Document No SPC SK6812 Rev No 03,www szledcolor com. Technical Data Sheet,13 The data structure of 24bit. G7 G6 G5 G4 G3 G2 G1 G0 R7 R6 R5 R4,R3 R2 R1 R0 B7 B6 B5 B4 B3 B2 B1 B0. Note high starting in order to send data G7 G6 B0,14 Electrical Optical Characteristics.
Forward Dominate Working,Color Luminance mcd,Voltage V Wavelength nm Current mA. Red 2 0 2 2V 700 1000 620 625 20,Green 3 0 3 2V 2200 3300 520 525 20. Blue 3 0 3 2V 1000 1500 465 470 20,15 The typical application circuit. 6 12 Document No SPC SK6812 Rev No 03,www szledcolor com. Technical Data Sheet,16 Standard LED Performance Graph.
Typical Relative Luminous Flux vs Forward Current Forward Voltage vs Forward Current. Forward Current mA,80 BLUE GREEN,60 BLUE GREEN,0 10 15 20 50 150 0 0 1 0 2 0 3 0 4 0 5 0. Forward Current mA Forward Voltage V Tj 25 C, Thermal Pad Temperature vs Relative Light Output Wavelength Characteristics. BLUE GREEN GREEN,Relative Emission Distribution,Normalized Luminous Flux. 0 20 40 60 80 100 120 400 450 500 550 600 650 700 750 800. Thermal Pad Temperature T 25 C Wavelength nm,Thermal Pad Temperature vs Forward Current. 100 Typical Radiation Pattern 120,Forward Current mA.
BLUE GREEN,0 90 75 60 45 30 15 0 0 2 0 4 0 6 0 8 1 0. 0 20 40 60 80 100 120 Radiation Angle,Thermal Pad Temperature C. 7 12 Document No SPC SK6812 Rev No 03,www szledcolor com. Technical Data Sheet,17 Packaging Standard,C A T H O D E ID E N T IF IC A T IO N. T A P E F E E D D IR E C T IO N C A R R IE R T A P E. COVER TAPE,R E E L 1 7 8 x 1 2 m m,IN N E R 1 0 0 0 p c s L E D M A X.
P R O D U C T N O S K 6 8 1 2,ESD PO LYETHYLENE BAG. Q U A N T IT Y 1 0 0 0 P C S,L o t N o L W 2 0 1 5 0 7 0 9 0 2 1 0. D A T E 2 0 1 5 0 7 0 9,L A B E L S K E T C H IN G. C A R D B O A R D IN N E R 4 0 B A G M A X, The reel pack is applied in SMD LED The LEDs are packed in cardboard boxes after packaging in normal or anti. electrostatic bags cardboard boxes will be used to protect the LEDs from mechanical shocks during transportation The. boxes are not water resistant and therefore must be kept away from water and moisture. 8 12 Document No SPC SK6812 Rev No 03,www szledcolor com.
Technical Data Sheet,TOP SMD LED Application Notes. 1 Features, The Purposes of making LEDCOLOR s customers and users to have a clear understanding on the ways how to. use the LED,2 Description, Generally The LED can be used the same way as other general purposed semiconductors When using. LEDCOLOR s TOP SMD LED the following precautions must be taken to protect the LED. 3 Cautions,3 1 Dust Cleaning, This emitter has a silicone surface There are many benefits to the silicone surface in terms of optical. properties and improved reliability However silicone is a softer material and prone to attract dust While a. minimal amount of dust and debris on the LED will not cause significant reduction in illumination steps. should be taken to keep the emitter free of dust, These include keeping the LEDs in the manufacturer s package prior to assembly and storing assemblies in.
an enclosed area after installing the emitters, Surface condition of this device may change when organic solvents such as trichloroethylene or acetone. were applied, Avoid using organic solvent it is recommended that isopropyl be used as a solvent for cleaning the LEDs. When using other solvents it should be confirmed beforehand whether the solvents will dissolve the. package and the resin of not, Do not clean the LEDs by the ultrasonic When it is absolutely necessary the influence as ultrasonic. cleaning on the LEDs depends on factors such as ultrasonic power Baking time and assembled condition. Before cleaning a pre test should be done to confirm whether any damage to the LEDs will occur. 3 2 Moisture Proof Package, In order to avoid the absorption of moisture during transportation and storage LED are packed in the. aluminum envelop A desiccant is included in the aluminum envelop as it absorbs moisture When. moisture is absorbed into the AMT package it may vaporize and expand during soldering There is a. possibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the. LEDs For this reason the moisture proof package is used to keep moisture to a minimum in the package. 3 3 Storage, In order to avoid the absorption of moisture It is recommended to store SMD LED in bulk or taped in the.
dry box or the desiccator with a desiccant Otherwise to store them in the following environment as. recommended,a Temperature 5 30 b Humidity 60 RH Max. It is recommended to solder the LED as soon as possible after unpacking the aluminum envelop But in case. that the LED have to be left unused after unpacking envelop again is requested. The LED should be soldering within 1 hours after opening the package. If baking is required A baking treatment should be performed as follows. 70 5 for more than 24 hours,9 12 Document No SPC SK6812 Rev No 03. www szledcolor com,Technical Data Sheet,3 4 Reflow Soldering Characteristics. In testing LEDCOLOR has found S50 LEDs to be compatible with JEDEC J STD 020C using the parameters listed below As a. general guideline LEDCOLOR recommends that users follow the recommended soldering profile provided by the manufacturer. of solder paste used, Note that this general guideline is offered as a starting point and may require adjustment for certain PCB designs and. Configurations of reflow soldering equipment,C ritical Zone T L to T P.
Temperature C,T 25 C to Peak, Profile Feature Lead Based Solder Lead Free Solder. Average Ramp Up Rate Ts max to Tp 3 second max 3 second max. Preheat Temperature Min Ts min 100 150,Preheat Temperature Min Ts max 150 200. Preheat Time ts min to ts max 60 120 seconds 60 180 seconds. Time Maintained Above Temperature TL 183 217, Time Maintained Above Time t L 60 150 seconds 60 150 seconds. Peak Classification Temperature T P 215 240, Time Within 5 of Actual Peak Temperature tp 10 seconds 10 seconds. Ramp Down Rate 6 second max 6 second max, Time 25 to Peak Temperature 6 minutes max 6 minutes max.
Note All temperatures refer to topside of the package measured on the package body surface. 10 12 Document No SPC SK6812 Rev No 03,www szledcolor com. Technical Data Sheet,3 5 Heat Generation, Thermal design of the end product is of paramount importance Please consider the heat generation of the. LED when making the system design The coefficient of temperature increase per input electric power is. affected by the thermal resistance of the circuit board and density of LED placement on the board as well as. components It is necessary to avoid in tense heat generation and operate within the maximum rating given in. this specification The operating current should be decided after considering the ambient maximum. temperature of LEDs,3 6 Electrostatic Discharge Surge Current. Electrostatic discharge ESD or surge current EOS may damage LED. Precautions such as ESD wrist strap ESD shoe strap or antistatic gloves must be worn whenever handling of. All devices equipment and machinery must be properly grounded. It is recommended to perform electrical test to screen out ESD failures at final inspection. It is important to eliminate the possibility of surge current during circuitry design. 3 7 Moisture Proof Package, Cannot take any responsibility for any trouble that are caused by using the LEDs at conditions exceeding. our specifications, The LED light output is strong enough to injure human eyes Precautions must be taken to prevent looking.
directly at the LEDs with unaided eyes for more than a few seconds. The formal specification must be exchanged and signed by both parties before large volume purchase begins. The appearance and specifications of the product may be modified for improvement without notice. 11 12 Document No SPC SK6812 Rev No 03,www szledcolor com. Technical Data Sheet,Change History,FCN No Date Rev No Changes Reason of changes. 2015 05 08 01 Initial Document,2015 07 09 02 Upgrade parameters. 2016 04 25 03 Luminous Intensity,Items Signatures Date. Prepared by Kevin Zhu 2016 04 25,Checked by,Approved by.
12 12 Document No SPC SK6812 Rev No 03,www szledcolor com. SK6812 is a set of smart control circuit and a light emitting circuit in reset after the end of DIN accept the data transmitted from the

Related Books