Powerswing

Powerswing-Free PDF

  • Date:05 Aug 2020
  • Views:5
  • Downloads:0
  • Pages:43
  • Size:1.83 MB

Share Pdf : Powerswing

Download and Preview : Powerswing


Report CopyRight/DMCA Form For : Powerswing


Transcription:

The New Besam Swing door operator,PowerSwing,Main models of the PowerSwing operator. Standard cover Special cover,Door leaf mounted Double door operators. The operator works electro hydraulically,Closing power from a coil spring. The open position is kept by a hydraulic valve, Lock kick to overcome the resistance of a striking plate. Dimension standard cover LxHxD 716x110x110 mm,Identification PowerSwing.
10 Extension unit EXA option,11 End plate, 1 Mounting plate 12 Programme selector PS 3 option. 2 Motor Pump 6 Spring tube 13 Cover,3 Valve 7 Cable inlet 14 Bearing sleeve. 4 Hydraulic unit 8 Mains connection 15 Cable holder. 5 Drive shaft 9 Control unit CSDA 16 Lid,Arm systems. PUSH Arm system PULL Arm system,Wall mounted operator arm system PUSH. Draw a line on the wall for the underside of the mounting plate. Door adaptor should,not be mounted on,glass bead,Extension has to be.
used if operator must,be mounted higher up,on the wall. Min 31 mm to,enable drive arm to,pass underneath,Wall mounted operator arm system PUSH. Cut out the appropriate template from the card board box. Ensure that the template aligns with the drawn line X and the C. Use the stickers in the mounting kit to fix the template to the wall. Punch where to drill,Wall mounted operator arm system PUSH. 1 Drill the four mounting holes and the two holes for the door fitting. 2 Remove the template, 3 Tap plug or reinforce with rivnuts and screw the drive unit tight. Mounting the PUSH drive arm, 1 Adaptor 1 Remove the door fitting from the arm system.
2 Drive arm 2 Screw the door fitting to the door leaf tight. 3 Mount the drive arm and adaptor on the operator drive shaft at an. angle of 90 to the wall, 4 Ensure that the teeth of the adaptor engage fully with the operator. shaft Tighten the screw to a torque of 25 Nm 19 lbf ft. Adjusting the PUSH arm,1 Open the door and connect the. door fitting with the drive arm do,not tighten the lock screws. 1 Telescopic part,2 Close the door and keep it closed. 2 Drive arm,3 Turn the drive arm until the,telescopic part is at an angle of 90.
to the door,4 Tighten the telescopic part with the. lock screws,Wall mounted operator and arm system PULL. Changing the direction of rotation,1 Mount the washer with the screw in the. drive shaft one from each side,2 Dismantle the screws 4 pcs from the. bearing sleeves on both sides,3 Fit the tools in the holes one from each.
side and turn both bearing sleeves,simultaneously approx 165 until the. setting lines in the bearing sleeves are,aligned with the setting lines in the. 4 Remount the four screws in the bearing,sleeves and dismantle the washers and. 5 Setting lines,Wall mounted operator arm system PULL. Draw a line on the wall for the underside of the mounting plate. Door adaptor should be,mounted aligned with,upper edge of the door.
Extension has to be,used if operator must be,mounted higher up on the. Wall mounted operator arm system PULL, Cut out the appropriate template from the card board box. Ensure that the template aligns with the drawn line Z and the CL1. Use the stickers in the mounting kit to fix the template to the wall. Punch where to drill,Wall mounted operator arm system PULL. 1 Drill the four mounting holes and the two holes for the door fitting. 2 Remove the template, 3 Tap plug or reinforce with rivnuts and screw the drive unit tight. Identification PowerSwing 6 Spring tube 7 Cable inlet Mains connection 9 Control unit CSDA Arm systems PUSH Arm system PULL Arm system Wall mounted operator arm system PUSH Decide X Draw a line on the wall for the underside of the mounting plate Door adaptor should not be mounted on glass bead Extension has to be used if operator must be mounted higher up on the wall

Related Books