OVAL POOL INSTRUCTIONS INYOpools com

Oval Pool Instructions Inyopools Com-Free PDF

  • Date:16 Oct 2020
  • Views:4
  • Downloads:0
  • Pages:35
  • Size:4.36 MB

Share Pdf : Oval Pool Instructions Inyopools Com

Download and Preview : Oval Pool Instructions Inyopools Com


Report CopyRight/DMCA Form For : Oval Pool Instructions Inyopools Com


Transcription:

INTRODUCTION, Congratulations on becoming the owner of a new Sharkline above ground swimming pool This is the. instruction packet for installing your swimming pool The following are some helpful hints that you should take. into consideration before installing your pool, 1 Read through the entire instruction booklet before you begin This will enable you to find out exactly what is. involved with installing your swimming pool before you begin While you are going through the instructions. please be aware that all of the diagrams are representative of a 15 x 30 18 x 33 pool If you have a different. size pool you will find that your pool has a different number of uprights than the ones in the diagrams. 2 DO NOT ATTEMPT INSTALLATION IN WINDY OR GUSTY WEATHER This will not only make. installation more difficult it may result in damage to your pool before it is completely installed. 3 Although we have broken down the installation into many simple steps you will probably find that steps one. and two will be the most labor intensive and time consuming steps Once you have completed those two steps. you should find that the rest of the installation moves along much more quickly. 4 Please be sure to review all safety material and local codes before beginning your installation There is a yellow. safety envelope packed with your pool This envelope contains safety material and warning stickers to be. placed on your pool If you are missing any of these items please contact your dealer or the factory to obtain it. The warranty is void if all safety precautions are not followed. 5 In the event that you need to make a warranty claim it is important to know the size and model of your. swimming pool in order to expedite the handling of your claim Please fill in the information below and keep. for your records,NAME OF POOL,SIZE OF POOL,DATE OF PURCHASE. NAME OF POOL WALL,NAME OF LINER, 6 Make sure you have the necessary tools and materials before beginning your installation. Below is a list of the tools and materials needed,Shovel Carpenters level and or transit.
Tape measure Patio Blocks 2 x 8 x 16,Phillips head screwdriver Box cutter Razor blade. Duct tape Tamp,Sand or pool base 5 16 wrench,Filter 1 4 wrench. Skimmer Return fitting,BUTTRESS FREE POOL SIZES,15 4 15 6 10 2 17 17 12. 10 x 16 12 x 17,17 18 12 17 20 4 5 12,12 x 18 12 x 20. 25 10 5 28 6,17 23 10 5 12 20 4 26 6 15 2,12 x 24 15 x 24.
Actual size of pool,Space needed for installation,BUTTRESS FREE POOL SIZES. 20 4 26 6 15 2 20 4 30 15 2,15 x 26 15 x 30,23 4 33 18 2 23 4 40 18 2. 18 x 33 18 x 40,23 4 43 6 18 2 23 4 42 6 18 2,18 x 44 21 x 43. Note All above diagrams are for Buttress Free oval pools If you have a traditional Buttress oval pool you will need. to add 3 feet to the width of the space needed for installation The length measurement will not change. Actual size of pool,Space needed for installation,INTRODUCTION. Congratulations on becoming the owner of a new above ground swimming pool This is the instruction packet. for installing your swimming pool The following are some helpful hints that you should take into consideration. before installing your pool, 1 Read through the entire instruction booklet before you begin This will enable you to find out exactly what is.
involved with installing your swimming pool before you begin While you are going through the instructions. please be aware that all of the diagrams are representative of a 15 x 30 18 x 33 pool If you have a different. size pool you will find that your pool has a different number of uprights than the ones in the diagrams. 2 DO NOT ATTEMPT INSTALLATION IN WINDY OR GUSTY WEATHER This will not only make. installation more difficult it may result in damage to your pool before it is completely installed. 3 Although we have broken down the installation into many simple steps you will probably find that steps one. and two will be the most labor intensive and time consuming steps Once you have completed those two steps. you should find that the rest of the installation moves along much more quickly. 4 Please be sure to review all safety material and local codes before beginning your installation There is a yellow. safety envelope packed with your pool This envelope contains safety material and warning stickers to be. placed on your pool If you are missing any of these items please contact your dealer or the factory to obtain it. The warranty is void if all safety precautions are not followed. 5 In the event that you need to make a warranty claim it is important to know the size and model of your. swimming pool in order to expedite the handling of your claim Please fill in the information below and keep. for your records All of this information can be found on the labels attached to the cartons your pool is packed in. NAME OF POOL,SIZE OF POOL,DATE OF PURCHASE,NAME OF POOL WALL. NAME OF LINER, 6 Make sure you have the necessary tools and materials before beginning your installation. Below is a list of the tools and materials needed,Shovel Carpenters level and or transit Optional. Tape measure Patio Blocks 2 x 8 x 16,Phillips head screwdriver Box cutter Razor blade. Duct tape Tamp,Sand 5 16 wrench,Filter 1 4 wrench,Skimmer Return fitting.
POOL LOCATION, Do not locate pool over underground lines BE SURE TO AVOID. septic tanks under electrical lines near hazardous. All electrical wires, structures or out of local code restrictions It is. All gas lines, essential that the area selected for your pool has. Septic tanks,a level and firm base Do not assemble your pool. on asphalt tar or oil base surfaces Avoid areas Cesspools. with sharp objects or ground treated with weed Dry wells. killer or other chemicals Also avoid areas where Tree roots stumps. nut grass Bermuda grass or bamboo grass grows buried debris trees. as they can grow through your liner Grass must building material etc. be removed Do not place components such as sudden slopes within 6. filters pumps and heaters in a way that they can of pool area. be used as a means of access to pool by young, children Be sure to follow all local building codes.
and obtain all building permits required for your area. STEP 1 PREPARING THE SITE, Refer to the True Size diagram on the second page to see the dimensions of your swimming pool Once you. have these measurements and have chosen a site to install your pool mark or outline the ground where the pool. will be going using spray paint or some other marking agent Please keep in mind that you will need some extra. room to work Be sure to account for the space that the side supports extend out on each side of an oval pool. The strap end channel extends out 37 from the wall of the pool on each of the two straight sides of a Traditional. Buttress oval If you have a Buttress Free oval pool system the strap end channel extends only 19 out from the. wall on each side Refer to the Actual Size chart for further clarification. For example a 15x30 oval should have the following space in order to install the pool. Traditional Buttress Oval Buttress Free Oval,23 4 30 15 2 20 4 30 15 2. Fig 2 15 x 30 Fig 2A 15 x 30, Once you have the appropriate area marked out remove any sod that is in the area Also be sure to avoid all electrical wires. gas lines septic tanks cesspools dry wells tree roots stumps buried debris and sudden slopes within 6 of the pool area. STEP 2 LEVELING, Once you have designated the space for installation and have cleared away the sod in that area you can begin. to level the ground The ideal tool for doing this is a transit If you do not have access to a transit use a long. board be sure that the board is perfectly straight and a carpenters level as shown in the diagram. The key to properly leveling the surface for an above ground swimming pool is to start at the lowest point and. dig everything else down to that level You do not want to build up the lower areas to be level with the higher. areas Doing this will cause the ground to settle once the pool is full of water If the ground settles it could. destroy your pool which could be dangerous and is not covered under the warranty. You will probably not be able to get the ground completely level until you lay out the frame but the closer you. get it now the easier the job will be later We recommend that you do not proceed until the entire site is within an. inch of being perfectly level, Remove soil and grass to this level Remove grass only from low areas.
DO NOT ADD DIRT TO LOW AREAS, STEP 4 PRE ASSEMBLING THE STRAIGHT SIDES OF A TRADITIONAL BUTTRESS OVAL POOL ONLY. THESE INSTRUCTIONS ARE FOR TRADITIONAL BUTTRESS OVAL POOLS ONLY IF YOU HAVE A BUTTRESS FREE. OVAL PLEASE USE ALTERNATE STEP FOUR, A Start by laying the strap end channels out on the ground so. that the open ends face down Notice the two slots on top of. each of these channels You will not be using these slots in. the construction of the pool but pay attention to where they Fig 7. are located in the diagrams They indicate which way the. channels are facing See Fig 7, B Now take the straight side 4 x4 Upright and push it down. over the strap end channel where those slots are located. Position the open end of the straight side upright to face the. short end of the channel the inside of the pool as shown. in Fig 8 The two holes on each side of the upright should. line up with two of the holes on each side of the strap end. channel Secure the parts with two 5 16 x 4 bolts and. two 5 16 nuts Repeat for all assemblies, C Once all of the straight side uprights are attached you can. begin attaching the struts This is done by pushing the. angled end of the strut the end with two holes on each. side over the end of the strap end channel and the other. side around the straight side upright The hole on each side. of the strut lines up with the hole in the straight side. upright that is farthest from the open end of the straight. side upright The two holes on the other end of the strut. line up with the only two holes in the back end of the strap. end channel Secure the struts using three 5 16 x 4 Fig 9. bolts and three 5 16 nuts See Fig 9 for visual instructions. PA RT I D E N T I F I E R, D Now you can install the straight side bottom rail connectors.
Use one per strap end channel Place the connector on top. of the strap end channel so that the open part of the. connector sits inside the straight side upright The hole. in the See Fig 10 for visual instructions straight side. connector will line up with the hole between the two slots. on the strap end channel Secure the piece using a, 12 x screw See Fig 10 for visual instructions Fig 10. Please do not be alarmed if you are not using all of the holes in the strap end channels We use this same. channel for a few different products so there are some holes that you will not be using for this pool. Please follow diagrams to be sure you are using all of the correct holes. ALTERNATE STEP 4, PRE ASSEMBLING THE STRAIGHT SIDES OF A BUTTRESS FREE OVAL POOL ONLY. IF YOU HAVE A TRADITIONAL BUTTRESS OVAL PLEASE REFER TO THE PREVIOUS STEP 4. A Start by laying out the under box channels so that the open. sides of each under box channel is facing up Then slide the. strap end channel over the top of the under box channels so. that they form a tube Be sure that the holes in both channels. are aligned but do not bolt them together yet See Fig 11 Fig 11. B Now slide the straight side 4 x4 uprights over the strap. end channels making sure that the holes line up as. shown in Fig 12, C Once the straight side 4 x4 uprights are attached apply the. left and right side gussets on each The pieces are marked. L and R The gussets are applied under the channels and. around the straight side upright Once you have them in. place screw the left and right gussets to each other using. three 10 screws See Fig 13 for visual instructions Fig 13. D All holes should be lined up at this point Bolt the components. 4 1 2 long, together as shown in the diagram Use 5 16 x 5 long bolts ss bolts. and 5 16 nuts for the channels and 5 16 x 4 long, stainless steel bolts for connecting the gussets to the uprights.
Remember to include the three hole washer at the fronts of. the gussets If these washers are left off your pool will break 5 long bolts. See Fig 14 for visual instructions,PA RT I D E N T I F I E R. E Once all of the 5 long bolts have been tightened install the. straight side bottom connectors This is done by placing the. connector on top of the strap end channel just inside the. straight side upright The hole in the connector should line. up with the hole in the strap end channel Secure the. connector to the channel using a single 12 x screw. for each as shown in Fig 15, Please do not be alarmed if you are not using all of the holes in the strap end channels We use this same. channel for a few different products so there are some holes that you will not be using for this pool You will. also have 3 extra 5 16 x 4 1 2 stainless steel bolts per upright when installing the Butress Free system. Please follow diagrams to be sure you are using all of the correct holes and hardware. STEP 5 STRAP ASSEMBLY FOR Traditional Buttress OVAL POOL ONLY. USE THIS STEP FOR TRADITIONAL BUTTRESS OVAL INSTALLATION ONLY IF YOU HAVE A BUTTRESS FREE OVAL. PLEASE SEE ALTERNATE STEP 5, Notice that there are two different sizes of strap packed with your pool Each strap is stamped with a part. OVAL POOL INSTRUCTIONS WARNING Your pool is designed for years of pleasurable safe family fun But when used incorrectly a swimming pool can be dangerous To insure your pool is used safely you must observe the following safety precautions Do not dive Do not jump No rough play No running or pushing Do not walk on the top rail It can be slippery and is not a walkway Be sure to

Related Books