Items Supplied gt Application s gt RevZilla com

Items Supplied Gt Application S Gt Revzilla Com-Free PDF

  • Date:23 Nov 2020
  • Views:6
  • Downloads:0
  • Pages:7
  • Size:439.56 KB

Share Pdf : Items Supplied Gt Application S Gt Revzilla Com

Download and Preview : Items Supplied Gt Application S Gt Revzilla Com


Report CopyRight/DMCA Form For : Items Supplied Gt Application S Gt Revzilla Com


Transcription:

23801 E La Palma Ave Yorba Linda Ca 92887 Ph 714 692 8180 Fax 714 692 5016. www fi2000r com,Instruction Manual 692 1606 Page 2 of 7. 06 07 DYNA INSTALLATION INSTRUCTIONS CONTINUED, 7 It is now time to install the oxygen sensor eliminator modules This product is designed to eliminate the. check engine light from coming on when the stock oxygen sensors are disconnected on 2006 Harley. Davidson Motorcycles utilizing fuel injection The motorcycle has a full open loop fuel injection map written. in its ECU and the motorcycle reverts to this default map after the oxygen sensors have been removed and. disconnected, 8 Locate the black waterproof connector in the wire harness bundle that is tucked down into the open area. under the seat Unplug the connector that comes from the rear oxygen sensor and replace that end with one. of the oxygen sensor eliminators, 9 Remove the two bolts holding the voltage regulator onto the lower front frame Let it drop down then directly. behind that is a black plastic panel that has a locking tab at the top Hinge that panel down to access the plugs. behind it Locate the front oxygen sensor connection slide it off its holding pin and unplug the connector. Replace the sensor wire end with our eliminator and then replace the connection onto its holding pin. Reinstall the panel and the voltage regulator, 10 Before re installing the seat and air cleaner assembly verify your connections NOTE The Fi2000R pot.
settings come preset from the factory for the 2007 DYNA and SOFTAIL Figure 7 for owners with a 2006. DYNA please adjust the Fi2000R to the base pot settings shown in Figure 8 prior to proceeding further. Remove the door from the Fi2000 box to expose the LED s Verify the wire connections by 1 turning the. ignition on prior to starting and see if all three LED s are on steady If you have no light your ground. connection BLACK wire has not made proper contact or your front injector connection is not complete 2. After achieving a steady light from all three LED s start the motorcycle wait 15 seconds and let it idle the. green light should now be the only LED on If all three LED s are still on after start up verify you have attached. the injector connectors correctly Reattach the door when finished Note Make sure the ignition is turned off. before changing any connection, 11 Remove the backing from the Velcro and attach the Velcro pad down between the back of the battery and the. ECU on the flat area of the frame Apply the mating Velcro to the back of the Fi2000R and attach see Figure. 1 Replace the rear fender wire harness above the Fi2000R. 12 Re install the seat and air cleaner assembly,07 SOFTAIL INSTALLATION INSTRUCTIONS. 1 Remove the seat and the aircleaner assembly Remove the rear fuel tank bolt and prop the rear of the fuel. tank up as far as it will comfortably go, 2 Locate the factory fuel injector connectors and by depressing the tab release the connectors from the injectors. see Figure 1, 3 Lay the Fi2000 module in the area underneath the seat feed the harness forward pushing it under the right. side of the factory harness hold down bracket see Figure 2 Now feed the Fi2000 harness into the factory. black plastic sleeve over the rear cylinder head make sure the harness rest into the bottom of the sleeve to. allow proper slack so the connectors reach the injectors. 4 Route the front set of Fi2000 connectors red and brown wires behind the existing wires and connect the gray. connector onto the injector Now insert the black connector into the original Harley connector Repeat for the. rear injector red and green wires Tuck the new set of connectors out of the way. 5 It is now time to install the oxygen sensor eliminator modules This product is designed to eliminate the check. engine light from coming on when the stock oxygen sensors are disconnected on 2006 Harley Davidson. Motorcycles utilizing fuel injection The motorcycle has a full open loop fuel injection map written in its ECU. and the motorcycle reverts to this default map after the oxygen sensors have been removed and disconnected. 6 At the front of the bike remove the 2 allen head bolts that hold the voltage regulator mounting bracket to the. block and remove the rectangular cover over the top of this bracket Ease the voltage regulator bracket. forward just enough to access the front oxygen sensor connection this may have already been done if the. exhaust is being changed Plug one of the supplied O2 eliminators into the connector on the harness then. position it back into its original position see Figure 5 Reinstall the voltage regulator and top cover Zip tie the. O2 sensor wire to the frame rail if leaving it in place. DOCUMENT NO 0018 REV A, 23801 E La Palma Ave Yorba Linda Ca 92887 Ph 714 692 8180 Fax 714 692 5016.
www fi2000r com,Instruction Manual 692 1606 Page 3 of 7. 07 SOFTAIL INSTALLATION INSTRUCTIONS CONTINUED, 7 The rear O2 connector is under the oil tank on the right side of the bike We recommend that you. temporarily remove the battery to gain access to this connector but you may attempt to install the O2. eliminator from underneath see Figure 6 If leaving the O2 sensor in place ziptie its harness to the starter. wire harness to prevent it from melting on the case. 8 If the battery has been removed reinstall it Attach the black wire to the NEGATIVE post of the battery Attach. the Fi2000 Module with Velcro as shown in Figure 4. 9 Before re installing the seat and air cleaner assembly verify your connections NOTE The Fi2000R pot. settings come preset from the factory for the 2007 DYNA and SOFTAIL Figure 7 for owners with a 2006. DYNA please adjust the FI2000R to the base pot settings shown in Figure 8 and refer to the previous. instructions set Remove the door from the Fi2000 box to expose the LED s Verify the wire connections by. 1 turning the ignition on prior to starting and see if all three LED s are on steady If you have no light your. ground connection BLACK wire has not made proper contact or your front injector connection is not. complete 2 After achieving a steady light from all three LED s start the motorcycle wait 15 seconds and let. it idle the green light should now be the only LED on If all three LED s are still on after start up verify you. have attached the injector connectors correctly Reattach the door when finished Note Make sure the. ignition is turned off before changing any connection. 10 Re install the seat and air cleaner assembly,ADVANCED TUNING. Your Cobra Fi2000 fuel injection module has been tested and preset for best function and ride ability on a. motorcycle with aftermarket aircleaner Cobra exhaust and no download ECU Flash The Fi2000 does. however have 3 important adjustments that allow you to tune the module for optimum performance especially. if you have performed other changes to your motorcycle These adjustments also allow you to resolve. drivability issues if our stock settings are not exactly right for your bike Make sure your motorcycle is up to. normal operating temperature 15 minutes of riding should be sufficient before making any adjustments. Remove the door to expose the pots shown in Figure 7 for 2007 DYNA and 2007 SOFTAIL models and Figure. 8 for 2006 DYNA models, GREEN LED POT left pot this adjustment affects idle and cruise fuel If you have cruising issues this is. where you would try a different setting Generally surging and uneven running while cruising is a lean fuel. condition so try adding a small increase in fuel by turning th e adjustment clockwise with a small flat blade. screwdriver a 1 2 of a position Test drive the bike to feel an improvement and only increase the setting until. the surge goes away Also backfiring or popping on trailing throttle is generally a lean sympto m or an exhaust. gasket leak Try the same small increases as above just until the backfiring goes away. YELLOW LED POT middle pot this adjustment affects acceleration and power fuel If you have a hesitation. or bogging on acceleration this is where you would try a different setting Aftermarket air cleaner assemblies. generally lean out fuel mixtures so try small clockwise increases as above until a smooth acceleration returns. RED LED POT right pot this adjustment is the top end or power fuel adjustment Just like the main jet in a. carburetor it starts to control fuel as you demand maximum power from your bike and takes over completely. above 4000 R P M As performance gains are added to your motorcycle such as big bore kits camshafts. flowed cylinder heads etc each component will increase the fuel demand of the system With the red. pot turned to its maximum 10 position the Fi2000 will cope with nearly 100 R W horsepower An all stock. motor will only require a 2 position You can generally if you are using quality performance engine upgrades in. a sensible combination equate the numbers evenly from 2 up to 10 based on horsepower gains. DOCUMENT NO 0018 REV A, 23801 E La Palma Ave Yorba Linda Ca 92887 Ph 714 692 8180 Fax 714 692 5016.
www fi2000r com,Instruction Manual 692 1606 Page 4 of 7. TUNING NOTES, Typically 2 into 1 or our speedster exhaust system require one additional position on the yellow and red pots. over slip ons or staggered duals, On high performance motors slip on mufflers do not flow well enough and create fuel setting problems and. detonation Cobra recommends the installation of any of its complete exhaust systems. TROUBLE SHOOTING, If you have any problems refer to step 9 in the main body of the instructions. Fi2000 MODULE,MOTORCYCLE,GROUND WIRE TO,DYNA 06 and Up.
H D CONNECTOR,TO FI CONNECTOR,H D CONNECTOR,FRONT FI2000. REAR FI2000,CONNECTOR TO,CONNECTOR FRONT OF,TO INJECTOR INJECTOR. MOTORCYCLE,DYNA 06 and Up,DOCUMENT NO 0018 REV A, 23801 E La Palma Ave Yorba Linda Ca 92887 Ph 714 692 8180 Fax 714 692 5016. www fi2000r com,Instruction Manual 692 1606 Page 5 of 7. REAR FEMALE FRONT FEMALE,H D CONNECTOR H D CONNECTOR.
WITH MALE Fi2000 WITH MALE Fi2000,CONNECTOR CONNECTOR. FEMALE Fi2000,WITH FRONT,FEMALE Fi2000,CONNECTOR FRONT OF. WITH REAR MOTORCYCLE,07 SOFTAIL,GROUND WIRE,TO NEGATIVE. BATTERY POST,INJECTOR WIRE,INSTALLATION,07 SOFTAIL. ZIPTIED TO,LEFT FRONT,FRAME RAIL,INSTALLATION,LOCATION OF.
ELIMINATOR,INSTALLATION WITH H D O2,LOCATION OF HARNESS. FRONT O2 BATTARY,SENSOR REMOVED FOR,ELIMINATOR,WITH H D O2. FIGURE 5 HARNESS FIGURE 6,07 SOFTAIL 07 SOFTAIL,DOCUMENT NO 0018 REV A. 23801 E La Palma Ave Yorba Linda Ca 92887 Ph 714 692 8180 Fax 714 692 5016. www fi2000r com,Instruction Manual 692 1606 Page 6 of 7. FIGURE 7 07 DYNA 07 SOFTAIL,Fi2000 Default pot setting.
Aftermarket Air Cleaner Exhaust,Download From Bulletin M 1186. Default Pot Settings,4 6 4 6 4 6,2 8 2 8 2 8,0 10 0 10 0 10. Green Yellow Red,Aftermarket Exhaust Only All Stock. Download From Bulletin M 1186 Download From Bulletin M 1186. Default Pot Settings Default Pot Settings,1 5 1 2 1 5 0 1. G Y R G Y R,4 6 4 6 4 6 4 6 4 6 4 6,2 8 2 8 2 8 2 8 2 8 2 8.
0 10 0 10 0 10 0 10 0 10 0 10,Green Yellow Red Green Yellow Red. DOCUMENT NO 0018 REV A, 23801 E La Palma Ave Yorba Linda Ca 92887 Ph 714 692 8180 Fax 714 692 5016. www fi2000r com,Instruction Manual 692 1606 Page 7 of 7. FIGURE 8 06 DYNA,Fi2000 Default pot setting,Aftermarket Air Cleaner Exhaust. No Downloads,Default Pot Settings,4 6 4 6 4 6,2 8 2 8 2 8.
0 10 0 10 0 10,Green Yellow Red,All Stock Aftermarket Air Cleaner Exhaust. No Downloads With 1 Download,Default Pot Settings Default Pot Settings. 2 5 4 2 2 5 2 3,G Y R G Y R,4 6 4 6 4 6 4 6 4 6 4 6. 2 8 2 8 2 8 2 8 2 8 2 8,0 10 0 10 0 10 0 10 0 10 0 10. Green Yellow Red Green Yellow Red, Stage 2 Motor 103cu In Cam Exhaust Stage 2 Motor 103cu In Cam Exhaust.
No Download With 2 Download,Default Pot Settings Default Pot Settings. 2 5 7 5 2 5 3 5,G Y R G Y R,4 6 4 6 4 6 4 6 4 6 4 6. 2 8 2 8 2 8 2 8 2 8 2 8,0 10 0 10 0 10 0 10 0 10 0 10. Green Yellow Red Green Yellow Red, If you have installed a Screamin Eagle air cleaner system the pot settings will need to be set 1. position lower than shown Example The green pot will need to be set at 1 5 instead of 2 5 etc. You can identify the Screamin Eagle air cleaner by the blue rubber rings. ATTENTION All 2007 Harley DYNA and SOFTAIL models manufactured before NOVEMBER 1 2006 require an ENGINE CONTROL MODULE CALIBRATION update from a Harley Davidson Dealer please reference Harley Davidson SERVICE BULLETIN M 1186 This Fi2000R is meant to function on all 2007 DYNA and SOFTAIL models with this update and all 2007 DYNA and SOFTAIL models manufactured after this date which should

Related Books