INSTALLATION INSTRUCTIONS 30095 BASE RAIL MOUNTING KIT

Installation Instructions 30095 Base Rail Mounting Kit-Free PDF

  • Date:24 Nov 2020
  • Views:4
  • Downloads:0
  • Pages:54
  • Size:2.04 MB

Share Pdf : Installation Instructions 30095 Base Rail Mounting Kit

Download and Preview : Installation Instructions 30095 Base Rail Mounting Kit


Report CopyRight/DMCA Form For : Installation Instructions 30095 Base Rail Mounting Kit


Transcription:

GENERAL INSTRUCTIONS FOR 30095 BASE RAIL INSTALLATION. 1 8 drill 3 4 Socket Open End Wrench 15 16 Socket,17 32 drill 100 lb ft Torque Wrench 21 32 drill. 1 1 4 Hole Saw Some Dodge applications only C Clamps 10 mm Socket Some applications. 1 The following instructions should be used to mount the Fifth wheel Care and attention to detail will ensure a quick quality installation. Check parts against parts list to become familiar with parts in kit See Fig 1. 2 Raise rear of truck high enough to allow jack stands to be placed under rear spring hanger bracket of truck This will provide maximum. room to install the Fifth wheel brackets, If the truck is raised be sure that the truck is properly blocked and restrained to prevent the truck. from falling Failure to do so may result in the truck suddenly falling causing death or serious injury. 3 Do not install mounting rails over plastic bed liners Plastic bed liners must be cut out of the way Base rails may be. installed on spray in liner Note Consult installer for recommended curing time. 4 Use only Cequent Performance Products Inc supplied bolts nuts and washers to install this kit Unless instructed otherwise All bolts. are Grade 5 and nuts are Grade 5 unless specified otherwise. 5 Specific instructions for most commonly used vehicles are included Each frame bracket must be bolted to the vehicle frame with two. bolts unless optional weld is used, These instructions are guidelines only Actual installation is the responsibility of the installer and the owner Always measure. truck and trailer before installing hitch to be sure that there is clearance at the cab and at the bumper to allow for turns. To prevent the trailer from hitting the cab with the trailer turned 90 the center of the hitch should be at least 52 from the back of the. cab when using a long bed truck Actual distance required will depend on trailer width and king pin location Short bed trucks Minimum. 38 from back cab to axle center line require a minimum of a 13 extended pin box with a Kwik slide or a SIDEWINDER Pinbox for regular. maneuvers DO NOT INSTALL ON OR ATTEMPT TO TOW WITH A TRUCK HAVING LESS THAN A 6 BED WITHOUT A SIDEWINDER PINBOX. INSTALLED ON THE TRAILER, 6 Measurements for rail placement are given from rear edge of truck bed to rear edge of the base rail closest to the rear edge of truck for. most vehicle applications, 7 Center hitch between fender wells and make sure rails are square Adjust position of rails until both diagonal measurements are the.
same This should allow installation of a gooseneck or other Fifth wheels to these rails. NOTE For ease of installation place the,unassembled fifth wheel support. Rear rail to rear,arches slider goose into the already edge of bed. installed rear mounting rail Position the measurement. forward mounting rail with the support FRONT,arches slider goose by inserting. the tabs into the mounting rail and, pushing the mounting rail tight towards Measure diagonally. the other mounting rail Ensure that the from same reference. mounting rail is centered on the bed of the point Measurement. vehicle This will position the rail in the correct. should be the same,location and ensure that the fifth wheel will.
have a snug fit to the truck, For Installation Assistance or Technical Help Call 1 888 521 0510. 30095N 6 13 14 REV K 2014 Cequent Performance Products Inc PRINTED IN CHINA 2. Check for obstructions before drilling Failure to do so could result in damaged fuel or brake lines structural. members etc Cequent Performance Products Inc does its best to communicate tow vehicle manufacturer. changes however it is ultimately the responsibility of the installer to prevent damage due to installation. 8 Mark 4 holes to be drilled through the truck bed see the illustrations for your truck Measure carefully to determine if the frame. bracket is under the hole in the rail you have chosen Hole location will vary for individual vehicle applications Drill 4 holes with 1 8. drill Be sure that the frame brackets will align with the 1 8 holes that were just drilled If they don t move either the frame brackets or. the rails slightly Drill another 1 8 hole and check again Then enlarge the 1 8 drilled holes with a 21 32 drill Always use sharp drill bits. Install tube spacer between rail and bed install 5 8 carriage bolts into holes Install filler spacer above or below bed to fill corrugations in. bed floor SEE FIG 4 on page 11 This is done to fill any space between the Frame bracket and the rail This will keep the bed corrugation. from crushing when the bolts are tightened, 9 Install mounting brackets onto carriage bolts Use the left and right angled frame brackets at locations where frame obstruction will not. allow the straight frame brackets to be positioned Secure bolts through mounting brackets with serrated washers and hex nuts. 10 Drill two 17 32 holes in truck frame for each frame bracket Select the holes which will give the greatest spread between bolts. Install eight 1 2 13x1 3 8 ribbed neck bolts threads pointing out serrated washers and hex nuts Tighten nuts until bolt heads seat. Lubrication of knurls of all rib neck bolts is recommended But only the knurled area See figure below for weld option. Note On vehicles with heavy duty suspensions check for interference with bolts where brackets are mounted to. frame If interference with suspension spring results cut bolt flush to nut outboard of frame or use weld option. DO NOT lubricate threads It may cause bolt failure. Check for obstructions before drilling Failure to do so could result in damaged fuel or brake lines. structural members etc Cequent Performance Products Inc does its best to communicate tow. vehicle manufacturer changes however it is ultimately the responsibility of the installer to prevent. damage due to installation, It is important that 17 32 drill be used for holes in chassis frame as rib neck bolts. may break if too small a hole is used and neck may not grip if too large a hole is used. 11 Torque all 1 2 nuts to 75 lb ft and all 5 8 nuts to 130 lb ft. 12 Pull wire provided to pull rib neck bolts through frame as needed per application See figure 1. OPTIONAL WELD ON APPLICATION FRONT REAR BRACKETS CAN BE. SWITCHED TO GET A BETTER FIT,CAN BE USED ON ALL TRUCKS. 1 4 2 00 1 4 2 00,1 4 2 00 1 4 2 00, 30095N 6 13 14 REV K 2014 Cequent Performance Products Inc PRINTED IN CHINA 3.
Chevy and GM 2011 Current 2500 HD 3500 HD Silverado and Sierra. Read pages 1 3 of these instructions before starting installation Failure to do so could result in significant vehicle damage. IMPORTANT NOTES FOR THIS INSTALLATION, 1 Find parallel rows of bed sill spot welds in bed of truck No drilling should be done in the approximately 4 between. parallel rows of spot welds where the bed sill sets. Rear Edge of,Vehicle Long Bed 29 11 16,Short Bed 25 3 16. Fifth wheel hitches over 18k,must have a center bolt in the. center hole in both rails,Measure from rear edge of. Note Place center bolt in the truck bed to rear edge of. hole that does not interfere base rail,with the bed sill If needed flip.
the rail around,Center bolts and hardware,are supplied with Fifth wheel. or gooseneck hitches that are,rated over 18k,Front of Optional weld. Vehicle pattern,Axle center,Long Bed Sills,Short Bed Sills Drivers side of 3 4 ton HD shown. Straight frame 1 4 2,bracket 1 4 2,Angled bracket,On inside of frame. Note Pull wire provided will be needed to install,hardware in brackets through frame.
Check for obstructions before drilling Failure to do so could result in damaged fuel or brake lines structural members etc. Cequent Performance Products Inc does its best to communicate tow vehicle manufacturer changes however it is ultimately. the responsibility of the installer to prevent damage due to installation. 30095N 6 13 14 REV K 2014 Cequent Performance Products Inc PRINTED IN CHINA 4. GM 99 Silverado Sierra not Sierra Classic models, Chevy GMC 00 to 10 Silverado Sierra including HD models and 04 up 1500 Crew. Cab with 5 8 bed Reese Sidewinder Pinbox required for 5 8 bed. Read pages 1 3 of these instructions before starting installation Failure to do so could result in significant vehicle damage. IMPORTANT NOTES FOR THIS INSTALLATION, 1 Find parallel rows of bed sill spot welds in bed of truck No drilling should be done in the approximately 4 between. parallel rows of spot welds where the bed sill sets. Rear Edge of,Front of Truck Bed,Fifth wheel hitches over. 18k must have a center Long Bed 31,bolt in the center hole in Short Bed 23 1 2. both rails,Note Place center bolt in,the hole that does not Measure from rear edge of.
interfere with the bed sill If truck bed to rear edge of. needed flip the rail around base rail,Center bolts and hardware. are supplied with Fifth,wheel or gooseneck Center,hitches that are rated over Hole. Optional weld, King Pin Center approx 3 1 2 Axle Center Left right angle and frame. forward of Axle Center brackets may be placed,wherever brackets fits best. Straight Bracket Bed Sill Drivers side of 3 4 ton,Chevy Long Box Shown.
Angled Bracket,Note Pull wire provided will be needed to install. hardware in brackets through frame, Check for obstructions before drilling Failure to do so could result in damaged fuel or brake lines structural members etc Cequent. Performance Products Inc does its best to communicate tow vehicle manufacturer changes however it is ultimately the responsibility of the. installer to prevent damage due to installation, 30095N 6 13 14 REV K 2014 Cequent Performance Products Inc PRINTED IN CHINA 5. CHEVROLET GMC 88 98 92 98 4 DOOR 99 SILVERADO, SIERRA CLASSIC WITH TAPERED FRAME RED TURN SIGNALS. Read pages 1 3 of these instructions before starting installation Failure to do so could result in significant vehicle damage. IMPORTANT NOTES FOR THIS INSTALLATION, 1 Find parallel rows of bed sill spot welds in bed of truck No drilling should be done in the approximately 4 between.
parallel rows of spot welds where the bed sill sets. Center Hole Rear Edge of,Inside Hole,Vehicle Long Bed 29 7 16. Short Bed 23 15 16,Fifth wheel hitches over,18k must have a center. bolt in the center hole in,both rails Measure from rear edge of. truck bed to rear edge of,Note Place center bolt in base rail. the hole that does not,interfere with the bed sill If.
needed flip the rail around,Center bolts and hardware. are supplied with Fifth,wheel or gooseneck Inside Hole. hitches that are rated over,18k Center Hole,King Pin Center. Front of over Axle Center Axle Center Left right angle and frame. Vehicle brackets maybe place where,ever brackets fits best. Bed Sill Drivers side 1 2 ton Long Box shown,Straight bracket Angle bracket.
1 4 1 5 3 1 4 2,1 4 2 1 4 2,Optional weld, Note Pull wire provided will be needed to install pattern. hardware in brackets through frame, Check for obstructions before drilling Failure to do so could result in damaged fuel or brake lines structural members etc. Cequent Performance Products Inc does its best to communicate tow vehicle manufacturer changes however it is ultimately. the responsibility of the installer to prevent damage due to installation. 30095N 6 13 14 REV K 2014 Cequent Performance Products Inc PRINTED IN CHINA 6. Chevrolet GMC 73 to 87 73 to 92 4 door 34 Straight with Inside Shock Absorbers. Read pages 1 3 of these instructions before starting installation Failure to do so could result in significant vehicle damage. IMPORTANT NOTES FOR THIS INSTALLATION, 1 Find parallel rows of bed sill spot welds in bed of truck No drilling should be done in the approximately 4 between. parallel rows of spot welds where the bed sill sets. Rear Edge of,Front of Truck Bed,Fifth wheel hitches over. 18k must have a center Long Bed 33 3 16,bolt in the center hole in Short Bed 23 3 16.
both rails,Note Place center bolt in,the hole that does not Measure from rear edge of. interfere with the bed sill If truck bed to rear edge of. needed flip the rail around base rail,Center bolts and hardware. are supplied with Fifth,wheel or gooseneck Center,hitches that are rated over Hole. King Pin Center approx,Long bed 3 1 2 short Axle Center. Left right angle and frame,bed over the Axle Center.
brackets maybe place where,Bed Sill ever brackets fits best. Straight Bracket,Drivers side of 1 2 ton Chevy Long Box Shown. 1 4 1 5 3 1 4 2,1 4 2 Optional weld,Angled Bracket. Note Pull wire provided will be needed to install,hardware in brackets through frame. Check for obstructions before drilling Failure to do so could result in damaged fuel or brake lines structural members etc. Cequent Performance Products Inc does its best to communicate tow vehicle manufacturer changes however it is ultimately. the responsibility of the installer to prevent damage due to installation. 30095N 6 13 14 REV K 2014 Cequent Performance Products Inc PRINTED IN CHINA 7. 2014 CURRENT RAM 2500 REQUIRES 58522 BRACKET KIT, Read pages 1 3 of these instructions before starting installation Failure to do so could result in significant vehicle damage.
IMPORTANT NOTES FOR THIS INSTALLATION, 1 Rib neck bolts will need to be pulled through rearward access holes in frame with supplied pull wire. 2 Do not drill thru both walls,of frame Drill only thru. INSTALLATION INSTRUCTIONS 30095 BASE RAIL MOUNTING KIT For Installation Assistance or Technical Help Call 1 888 521 0510 1 Provide this Manual to end user 2 Physically demonstrate procedures in this Manual to end user 3 Have end user demonstrate that he she understands procedures 1 Read and follow this Manual every time you use Hitch 2 Save this Manual for future reference 3

Related Books