BQ 260 F Monografias com

Bq 260 F Monografias Com-Free PDF

  • Date:25 Nov 2020
  • Views:3
  • Downloads:0
  • Pages:93
  • Size:2.73 MB

Share Pdf : Bq 260 F Monografias Com

Download and Preview : Bq 260 F Monografias Com


Report CopyRight/DMCA Form For : Bq 260 F Monografias Com


Transcription:

Safety Precautions, The signal word WARNING indicates a potentially hazardous situation which if not. avoided could result in death or serious injury, The signal word CAUTION indicates a potentially hazardous situation which if not. avoided may result in damage on machines It may also be used to alert against unsafe. Read and understand all safety instructions with signal word such as WARNING and. CAUTION If safety instructions are ignored personal injury will result. Horizon International Inc cannot anticipate every possible situation that might involve. a potential hazard The instruction in this manual and warning labels on the machine are. therefore not all inclusive, All equipment shall be locked out or tagged out to protect against accidental or inad. vertent operation when such operation could cause injury to personnel Do not attempt to. operate any switch valve or other energy isolating device where it is locked or tagged out. Do not operate the machines with any covers being removed. Some of the drawings in this manual shows the machine uncovered for explaining the. detail or inside of machine,Important Information I. Safety Precautions II,1 Machine Parts Descriptions.
1 1 General View of BQ 260 2,1 2 Control Panel 3,1 3 Operation Panel 5. 1 4 Accessories and Tools 6,1 5 Accessory Tools 7,2 Installation Instructions. 2 1 Installation Instructions 10,2 1 1 Installing Place 10. 2 1 2 Installing BQ 260 10,2 1 3 Installing Cover Feeder Unit on BQ 260 11. 2 1 4 Attach Dust Bag 11,2 1 5 Releasing Transport Lock Nut 12.
2 1 6 Connecting Power Cord 12,3 Before Starting Operation. 3 1 Safety Device Function Check 16,3 1 1 Stop Button 16. 3 1 2 Safety Cover 18,3 2 Every Day Check Up 20,3 2 1 Glue Level Check 20. 3 2 2 Level Plate Cleaning Check 20,3 2 3 Nipper Unit Check 21. 3 2 4 Dust Bag Check 21,4 Set Up BQ 260,4 1 Nipper Unit Set Up 24.
4 1 1 Nipper Unit Set Up for Stock Thickness 24,4 1 2 Cover Positioning Set Up 26. 4 2 Clamper Unit Set Up 28,4 3 Milling Unit Set Up 29. 4 3 1 Milling Guide Set Up 29,4 3 2 Milling Depth Set Up 30. 4 4 Cover Feeder Unit Set Up 31,4 4 1 Cover Feeder Position Set Up 31. 4 4 2 Cover Feeder Position Set Up for Cover longer than 550 mm 34. 4 4 3 Attachment of Accessories 36,4 4 4 Test Feed of Cover 37.
4 5 Vertical Stacker Unit Set Up 38,4 6 Melt Tank Unit Set Up 39. 4 7 Operation Switches Set Up 41,4 8 Test Binding 42. 4 8 1 Test Binding for With Milling Binding 42,4 8 2 Pad Binding 44. 5 Operation Procedure,5 1 With Cover Binding Operation 46. 5 2 Pad Binding 48,6 Special Binding Method,6 1 Small Size Binding 52.
6 1 1 Register Shaft Position Adjustment 52, 6 1 2 Cover Position Register Block Installation 53. 6 1 3 Small Cover Stopper Installation 54,6 1 4 Shooter Attachment 55. 6 2 To Increase Glue Film Thickness 56,6 2 1 Spacer Plate Attachment 56. 6 2 2 Melt Tank Height Adjustment 59,6 3 To Adjust Condition of Spine 60. 7 After Binding Finish,7 1 Glue Supply 62,7 2 Clean Up While Power On 63.
7 2 1 Nipping Plate and Nipper Jaw Clean Up 63,7 2 2 Level Plate Clean Up 64. 7 3 Clean Up after Power Off 66,7 3 1 Dust Bag Clean Up 66. 7 3 2 Vertical Stacker Unit Clean Up 66,7 4 Clean Up after Power Off 67. 7 4 1 Milling Unit Clean Up 67,7 4 2 Gluing Length Sensor Clean Up 68. 7 4 3 Cover Sensor Clean Up 68,8 Maintenance,8 1 Once A Month 70.
8 1 1 Lubrication on Melt Tank Unit 70,8 1 2 Greasing on Clamper Rail 70. 8 1 3 Oiling on Nipper Unit 70,8 2 As Required 71,8 2 1 Milling Cutter Replacement 71. 8 2 2 Roughening Cuter Replacement 72,8 2 3 Glue Draining 74. 9 Installation of Suction Cover Feeder CF 260 Optional Equipment. 9 1 Before You Begin 76,9 1 1 Specifications 76,9 1 2 Machine Descriptions and Functions 76. 9 1 3 Descriptions and Functions of Operation Panel 77. 9 1 4 Tools and Accessories 78,9 2 Set Up and Operation 79.
9 2 1 Cover Piling 79,9 2 2 Open Close of Sucker Valve 80. 9 2 3 Cover Feeder Position Set Up 80,9 2 4 Support Plate Set Up 80. 9 2 5 Attachment of Accessories 81,9 2 5 Feeding Test 82. 9 2 6 Cover Piling 82,9 2 7 Binding Finish 83,9 3 Trouble Shooting 84. 9 3 1 When Misfeed Occurs 84,9 3 2 When Two Covers are fed at the same time 85.
9 4 Installation of BQ 260 86,1 Machine Parts Descriptions. 1 Machine Parts Descriptions,1 1 General View of BQ 260 2. 1 2 Control Panel 3,1 3 Operation Panel 5,1 4 Accessories and Tools 6. 1 5 Accessory Tools 7,1 Machine Parts Descriptions. 1 1 General View of BQ 260,Safety Cover Melt Tank Unit.
Clamper Unit,Milling Unit,Nipping Unit,Level Plate. Vertical Stacking Section Control Panel,Cover Feeding Unit. 1 Machine Parts Descriptions,1 2 Control Panel,1 2 3 4 5 6. Trouble Monitor,7 8 9 10 11 12 13, 1 Gluing Length Adjusting Knobs 8 Milling Mode Select Switch. Used to adjust spine glue length Used to select milling mode with milling. or without milling,2 Milling Start Button, Used to start to rotate milling cutter 9 Level Plate Mode Select Switch.
Used to select reset mode of Level Plate, 3 Cover Single Feed Button after one complete cycle of binding. Used to feed one cover sheet from cover automatic or manual. feeder with automatic cover feeding,mode 10 Cover Feed Mode Select Switch. Used to select cover feed mode auto,4 Nipper Up Down Button matic or manual. Used to raise or lower nipper unit for, setting up nipping unit 11 Clamper Pin On OFF Switch. Used to turn on off clamper pin which, 5 Nipping Time Control Knob holds stock in clamper when without.
Used to control nipping time milling mode is selected. 6 Nipping Mode Select Switch 12 Nipping Delay Time Control Knob. Used to select nipping mode Three Used to control nipping delay time. different modes With milling binding length,mode Signature binding mode and Pad. binding mode can be selected 13 Pad Binding Lamp,This lamp turns on when pad binding. 7 Trouble Monitor mode is selected,Please refer to next page. 1 Machine Parts Descriptions,1 2 Control Panel,Trouble Monitor. Trouble Monitor,Indicates incorrect point on BQ 260.
When one of them turns on except power,lamp BQ 260 can not be started. Each LED turns on when lease it,1 safety cover opens. Close safety cover 5 glue is not ready for biding,Wait until glue will be melted. 2 milling cutter does not rotate although, with milling binding mode is selected 6 cover is not fed to stopper. Depress milling cutter start button to Feed cover completely until it gets. rotate milling cutter stopped against stopper,3 level plate opens 7 main power is on.
Depress start button to reset level plate,4 emergency stop switch is depressed. Pull up emergency stop switch to re,NOTE Difference of Nipper Movement. Nipping unit has two different movements with milling binding mode and signature bind. ing mode In with milling binding mode nipper plate raises at first and then front and back. nipper jaws nip stock So this binding mode is suitable for binding milled stock or cut sheet. stock In signature binding mode nipper plate and two nipper jaws raise and nip stock at. same time So this binding mode is suitable for binding signature which spine is shaped. thicker because of folded edge Book spine will be formed too sharp or destroyed when. spine is pressed at first as in with milling binding mode Binding quality or book spine. shape bound with signature binding mode is not affected so much by folding. With Milling Binding Mode Signature Binding Mode,1 Machine Parts Descriptions. 1 3 Operation Panel,1 Counter with reset button, Used to count amount of binding When 3 Start Lamp and Start Button. reset button is set at far side number in Lamp indicates that BQ 260 is ready to. counter can not be reset bind,2 Level Plate Button 4 Stop Button.
Used to open and reset level plate manually,when level plate switch is set at manual. operation mode,1 Machine Parts Descriptions,1 4 Accessories and Tools. Check all accessories are supplied with your BQ 260 when you open package. 1 Cover Feed Unit 1 set 8 Drain for Glue Replacement 1 pc. 9 Dust Bag 1 pc,2 Feed Roller Cleaner 2 sets, 3 Support Plates for Cover Feeder Unit 10 Cover Feeding Supporter 1 pc. Large 1 pc,Small 1 pc, 4 Small Cover Stopper 1 pc 11 Cover Feed Roller 1 pc. 12 Milling Cutter 1 pc,5 Small Cover Position Register 2 sets.
13 Grease 1 pc,6 Clamper Support Guide,Large 1 pc,Normal 1 pc. 14 Chain Oil 1 pc,7 Space Plate 1 pc,1 Machine Parts Descriptions. 1 4 Accessories and Tools, 15 Hot Melt HM 110 5 kg 17 Shooter for small book 1 pc. 16 Mount Base with Leveling Bolt 3 sets 18 Feed Cover 1 pc. 1 5 Accessory Tools, Check all tools supplied with your BQ 260 when you open package. 1 Screw Driver 1 pc 5 Special Wrench 1 pc,2 Spanner 30 mm 1 pc.
6 Allen Wrench 2 5 3 4 5 6 mm,1 pc of each,3 Spanner 13 17 mm 1 pc. 7 Roughening Cutter Height Gauge 1 pc,4 Pipe Wrench 30 mm 1 pc. 1 Machine Parts Descriptions,2 Installation Instructions. 2 Installation Instructions,2 1 Installation Instructions 10. This manual is designed to help you to install operate and maintain Perfect Binder BQ 260 260L Read understand and keep this manual in a safe and convenient place Do not operate BQ 260 260L until you read and understand the instructions in this manual Horizon International Inc shall not be liable for incidental consequential damages

Related Books