Boom T ruck Crane 0 R 7010 Clark Rigging

Boom T Ruck Crane 0 R 7010 Clark Rigging-Free PDF

  • Date:07 Mar 2020
  • Views:26
  • Downloads:0
  • Pages:8
  • Size:897.54 KB

Share Pdf : Boom T Ruck Crane 0 R 7010 Clark Rigging

Download and Preview : Boom T Ruck Crane 0 R 7010 Clark Rigging


Report CopyRight/DMCA Form For : Boom T Ruck Crane 0 R 7010 Clark Rigging


Transcription:

BOOM TRUCK CRANE,STINGER 70100, CAUTION Do not use this specification sheet as a load rating chart The format of data. LOAD RATINGS is not consistent with the machine chart and may be subject to change. BOOM LENGTH Maximum Load Chart in pounds lbs with fully extended outrigger. 30 5 FT 44 FT 58 FT 72 FT 86 FT 100 FT, OPERATING LOADED LOAD LOADED LOAD LOADED LOAD LOADED LOAD LOADED LOAD LOADED LOAD. RADIUS BOOM RATING BOOM RATING BOOM RATING BOOM RATING BOOM RATING BOOM RATING. FT ANGLE LB ANGLE LB ANGLE LB ANGLE LB ANGLE LB ANGLE LB. AREA OF OPERATION,DEG DEG DEG DEG DEG DEG,DO NOT OPERATE. 5 78 70 000 IN SHADED AREA,8 72 60 800 WITHOUT,10 68 44 800 75 31 300 OPTIONAL FRONT. 12 64 40 000 72 31 700 77 31 100 STABILIZER,15 58 33 200 68 31 600 74 30 500 77 27 600.
20 45 24 400 61 24 500 68 23 600 73 21 200 76 19 000. 25 29 18 300 53 19 100 63 19 100 69 17 200 72 15 300 75 12 100. 30 44 15 000 57 15 400 64 14 400 69 12 900 72 10 500. 35 34 11 400 51 11 800 60 12 000 65 11 100 69 9 100. 40 18 8 700 44 9 300 55 9 400 61 9 500 66 7 000,45 36 7 300 50 7 600 57 7 700 62 6 000. 50 NOTE STRUCTURAL STRENGTH RATINGS IN 27 5 800 44 6 100 53 6 200 59 5 100. 55 CHART ARE INDICATED WIH AN ASTERISK 11 4 600 38 5 000 49 5 100 56 4 500. 60 31 4 000 44 4 200 52 3 900,65 22 3 200 39 3 400 48 3 400. 70 34 2 800 44 2 900,75 27 2 200 40 2 400,Deductions from rate. 80 18 1 700 35 1 900 loads for load handling,85 30 1 500 devices BT. 90 24 1 100,95 15 800 Overhaul Ball 200 lbs, STOWED JIB DEDUCTIONS POUNDS 1 Sheave Load Block 225 550 lbs.
900 700 500 400 335 300 2 Sheave Load Block 300 650 lbs. JIB CAPACITIES FOR ALL BOOM LENGTHS VERIFY OPERATIONAL MODE SETTING ON LMI DISPLAY BEFORE LIFTING WITH JIB. Loaded Boom Angle 50 55 60 65 70 75 78 80, Retracted 30 5 ft Jib 800 1 400 2 300 3 300 4 000 5 300 6 000 6 450. Extended 55 ft Jib 700 1 050 1 700 2 300 3 000 3 500 3 500 3 500. RANGE DIAGRAM 30 5 100 FT BOOM,GENERAL NOTES, 1 The operator must read and understand the Owner s Manual before operating this crane. 2 Positioning or operation of crane beyond areas shown on this chart is not intended or approved except where. specified in Owner s Manual, 3 Loaded boom angles at specified boom lengths give only an approximation of the operating radius The boom angle. before loading should be greater to account for deflections Do not exceed the operating radius for rated loads. 4 Use rating of next longer boom for boom lengths not shown Use rating of next greater radius for load radii not shown. 5 Boom must be fully retracted when jib is erected before lowering below minimum angle Retracted jib has no lifting. capacity below a 50 boom angle,CENTERLINE OF ROTATION. SHEAVE HEIGHT FEET, 6 Use rating of next lower boom angle for boom angles not shown on jib load rating chart.
7 Lifting off the main boom point while the swing around jib is erected is not intended or approved. 8 Do not lower boom into this area as hydraulic pressure will not allow raising the boom without retracting boom first. 9 Crane load ratings on outriggers are based on freely suspended loads with the machine leveled and standing on a firm. uniform supporting surface No attempt shall be made to move a load horizontally on the ground in any direction. 10 Practical working loads depend on supporting surface wind and other factors affecting stability such as hazardous. surroundings experience of personnel and proper handling must all be taken into account by the operator. 11 The maximum load which may be telescoped is limited by hydraulic pressure boom angle and boom lubrication It is. safe to attempt to telescope any load within the limits of the load rating chart. INFORMATION, 1 Deductions must be made from rated loads for stowed jib optional attachments hooks and loadblocks see deduction. chart Weights of slings and other load handling devices shall be considered a part of the load. 2 Crane load ratings with outriggers are based on outriggers and stabilizers extended and set with all load removed. from the carrier wheels,3 Load ratings do not exceed 85 of tipping load. DEFINITIONS, 1 Operating radius is the horizontal distance from the axis of rotation to the center of the vertical hoist line or load hook. with load suspended, 2 Loaded boom angle as shown in the Load Ratings Chart is the included angle between the horizontal and longitudinal. axes of the boom base after lifting rated load at rated radius. BOOM TRUCK CRANE,STINGER 70100, CAUTION Do not use this specification sheet as a load rating chart The format of data.
LOAD RATINGS is not consistent with the machine chart and may be subject to change. BOOM LENGTH Maximum Load Chart in pounds lbs with fully extended outrigger. 30 5 FT 44 FT 58 FT 72 FT 86 FT 100 FT, OPERATING LOADED LOAD LOADED LOAD LOADED LOAD LOADED LOAD LOADED LOAD LOADED LOAD. RADIUS BOOM RATING BOOM RATING BOOM RATING BOOM RATING BOOM RATING BOOM RATING. FT ANGLE LB ANGLE LB ANGLE LB ANGLE LB ANGLE LB ANGLE LB. DEG DEG DEG DEG DEG DEG AREA OF OPERATION,360 Full Capacity. 5 74 70 000 Area of,8 67 44 900 Operation,10 63 39 000 72 31 100. 12 59 34 400 69 31 100 74 31 100,15 52 29 190 65 27 800 71 26 700 75 24 200. 20 38 22 300 57 22 000 66 21 200 71 19 200 74 17 000. 25 17 14 900 49 18 000 60 17 500 67 16 000 71 14 400 73 12 100. 30 40 14 800 54 14 700 62 13 300 67 12 000 70 10 500. 35 27 11 600 48 12 000 57 11 500 63 10 300 67 9 100. 40 41 9 200 53 9 400 59 9 100 64 6 500,45 32 7 200 47 7 400 55 7 500 61 5 600.
NOTE STRUCTURAL STRENGTH RATINGS IN, 50 CHART ARE INDICATED WIH AN ASTERISK 21 5 700 42 5 900 51 6 000 58 4 900. 55 35 4 700 47 4 900 54 4 200,60 27 3 800 42 3 900 50 3 600. 65 16 3 000 37 3 200 47 3 100,70 31 2 500 42 2 600. Deductions from rate,75 23 2 000 38 2 100 loads for load handling. 80 12 1 500 33 1 600 devices BT,85 27 1 200,90 20 900 Overhaul Ball 200 lbs.
95 7 600 1 Sheave Load Block 225 550 lbs, STOWED JIB DEDUCTIONS POUNDS 2 Sheave Load Block 300 650 lbs. 900 700 500 400 335 300, JIB CAPACITIES FOR ALL BOOM LENGTHS VERIFY OPERATIONAL MODE SETTING ON LMI DISPLAY BEFORE LIFTING WITH JIB. Loaded Boom Angle 50 55 60 65 70 75 78 80, Retracted 30 5 ft Jib 800 1 400 2 300 3 300 4 000 5 300 6 000 6 450. Extended 55 ft Jib 700 1 050 1 700 2 300 3 000 3 500 3 500 3 500. RANGE DIAGRAM 30 5 100 FT BOOM GENERAL NOTES, 1 The operator must read and understand the Owner s Manual before operating this crane. 2 Positioning or operation of crane beyond areas shown on this chart is not intended or approved except where. specified in Owner s Manual, 3 Loaded boom angles at specified boom lengths give only an approximation of the operating radius The boom angle.
before loading should be greater to account for deflections Do not exceed the operating radius for rated loads. 4 Use rating of next longer boom for boom lengths not shown Use rating of next greater radius for load radii not shown. CENTERLINE OF ROTATION,SHEAVE HEIGHT FEET, 5 Boom must be fully retracted when jib is erected before lowering below minimum angle Retracted jib has no lifting. capacity below a 50 boom angle, 6 Use rating of next lower boom angle for boom angles not shown on jib load rating chart. 7 Lifting off the main boom point while the swing around jib is erected is not intended or approved. 8 Do not lower boom into this area as hydraulic pressure will not allow raising the boom without retracting boom first. 9 Crane load ratings on outriggers are based on freely suspended loads with the machine leveled and standing on a firm. uniform supporting surface No attempt shall be made to move a load horizontally on the ground in any direction. 10 Practical working loads depend on supporting surface wind and other factors affecting stability such as hazardous. surroundings experience of personnel and proper handling must all be taken into account by the operator. 11 The maximum load which may be telescoped is limited by hydraulic pressure boom angle and boom lubrication It is. safe to attempt to telescope any load within the limits of the load rating chart. INFORMATION, 1 Deductions must be made from rated loads for stowed jib optional attachments hooks and loadblocks see deduction. chart Weights of slings and other load handling devices shall be considered a part of the load. 2 Crane load ratings with outriggers are based on outriggers and stabilizers extended and set with all load removed. from the carrier wheels,3 Load ratings do not exceed 85 of tipping load. DEFINITIONS, 1 Operating radius is the horizontal distance from the axis of rotation to the center of the vertical hoist line or load hook.
with load suspended, 2 Loaded boom angle as shown in the Load Ratings Chart is the included angle between the horizontal and longitudinal. axes of the boom base after lifting rated load at rated radius. BOOM TRUCK CRANE,STINGER 70100,WINCH DATA BLOCK TYPE. 1 Part Line 2 Part Line 3 Part Line 4 Part Line 5 Part Line 6 Part Line Overhaul Ball Rating 7 0 ton 6 3 mt. 1 Sheave Block Rating 20 ton 18 1 mt,2 Sheave Block Rating 30 ton 27 2 mt. 3 Sheave Block Rating 35 ton 31 7 mt,ONE ONE TWO TWO THREE. OVERHAUL SHEAVE SHEAVE SHEAVE SHEAVE SHEAVE,BALL LOAD LOAD LOAD LOAD LOAD.
BLOCK BLOCK BLOCK BLOCK BLOCK, Cable Lift and Lift and Lift and Lift and Lift and Lift and Overload and anti two block systems must be in good. Supplied Speed Speed Speed Speed Speed Speed operating condition before operating crane Refer to. Owners Manual, 5 8 Diam 12 971 lb 25 942 lb 38 913 lb 51 844 lb 64 855 lb 70 000 lb. Standard IWRC XXIP 196 fpm 98 fpm 65 fpm 49 fpm 39 2 fpm 32 7 fpm Keep at least 3 wraps of loadline on drum at all times. Stationary, Winch 5 8 Diam 9080 lb 18 160 lb 27 240 lb 36 320 lb 45 400 lb 54 480 lb Use only 5 8 diameter cable with 45 400 lb breaking. Rotation Resistant 196 fpm 98 fpm 65 fpm 49 fpm 39 2 fpm 32 7 fpm strength on this machine. 2 MOUNTING CONFIGURATIONS,CARRIER PROVIDED BY TEREX INCLUDED OPTIONS. STINGER BT70100 Behind Cab Mounting Configuration Dual Fuel Tanks 120 gal 454L. Manufacturer Sterling LT7501 6 x 4 60 000 Power steering. Standard Engine Caterpillar C 7 7 2 L I 6 Electric Horn. Standard Horsepower 300 hp 2 200 rpm Factory A C, Standard Torque 860 Ib Ft 1 440 rpm Power Port Cigar lighter.
Full Tank Capacity 120 gal 454 L AM FM Radio w Clock. Standard Transmission Eaton Fuller RT 8908LL Dual West Coast Stainless Rear View Mirrors. Speed Standard Transmission Manual 10 speed Standard Factory Warranty. Max Speed Standard Transmission 74 mph 120 km h,Max Gradeability 54 CHASSIS RECOMMENDATIONS. Standard Transmission STINGER BT70100 Behind Cab Mounting Configuration. Optional Transmission Allison Combined Axle Weight Rating 60 000 Ib 27 210 kg. Speed Optional Transmission Automatic 6 speeds Front Axle Weight Rating 20 000 Ib 9 067 kg. Max Speed Optional Transmission 74 mph 120 km h Rear Axle Weight Rating 40 000 Ib 18 144 kg. Max Gradeability 17 Wheel base 261 6 62 m,Optional Transmission Cab to Axle 192 4 87 m. Gross Vehicle Weight Rating 60 000 Ib 27 210 kg Afterframe 114 2 90 m. Front Axle Weight Rating 20 000 Ib 9 067 kg Frame Section Modulus 30 0 in3 491 cm3. Rear Axle Weight Rating 40 000 Ib 18 144 kg RBM per Frame Rail 3 300 000 in Ib 38 020 kg m. Front Tires 425 65R 22 5 Michelin XZY 20 ply Frame Height Unloaded 40 7 62 m. Rear Tires 11R 22 5 Michelin XDE M S 14 ply Exhaust Position Vertical Right Side. Brakes Air Hydraulic Anti Lock System,Exhaust Position Vertical Right Side. BOOM TRUCK CRANE,STINGER 70100,WINCH DATA BLOCK TYPE. 1 Part Line 2 Part Line 3 Part Line 4 Part Line 5 Part Line 6 Part Line Overhaul Ball Rating 7 0 ton 6 3 mt. 1 Sheave Block Rating 20 ton 18 1 mt,2 Sheave Block Rating 30 ton 27 2 mt.
3 Sheave Block Rating 35 ton 31 7 mt,ONE ONE TWO TWO THREE. OVERHAUL SHEAVE SHEAVE SHEAVE SHEAVE SHEAVE,BALL LOAD LOAD LOAD LOAD LOAD. BLOCK BLOCK BLOCK BLOCK BLOCK, Cable Lift and Lift and Lift and Lift and Lift and Lift and Overload and anti two block systems must be in good. Supplied Speed Speed Speed Speed Speed Speed operating condition before operating crane Refer to. Owners Manual, 5 8 Diam 12 971 lb 25 942 lb 38 913 lb 51 844 lb 64 855 lb 70 000 lb. Standard IWRC XXIP 196 fpm 98 fpm 65 fpm 49 fpm 39 2 fpm 32 7 fpm Keep at least 3 wraps of loadline on drum at all times. Stationary, Winch 5 8 Diam 9080 lb 18 160 lb 27 240 lb 36 320 lb 45 400 lb 54 480 lb Use only 5 8 diameter cable with 45 400 lb breaking.
Rotation Resistant 196 fpm 98 fpm 65 fpm 49 fpm 39 2 fpm 32 7 fpm strength on this machine. 2 MOUNTING CONFIGURATIONS,CARRIER PROVIDED BY TEREX INCLUDED OPTIONS. STINGER RS70100 Riding Seat Mounting Configuration Dual Fuel Tanks 120 gal 454 L. Manufacturer Sterling LT7501 6 x 4 60 000 Power steering. Standard Engine Caterpillar C 7 7 2 L I 6 Electric Horn. Standard Horsepower 300 hp 2 200 rpm Factory A C, Standard Torque 860 Ib Ft 1 440 rpm Power Port Cigar lighter. Full Tank Capacity 120 gal 454 L AM FM Radio w Clock. Standard Transmission Eaton Fuller RT 8908LL Dual West Coast Stainless Rear View Mirrors. Speed Standard Transmission Manual 10 speed Standard Factory Warranty. Max Speed Standard Transmission 74 mph 120 km h,Max Gradeability 54 CHASSIS RECOMMENDATIONS. Standard Transmission STINGER RS70100 Riding Seat Mounting Configuration. Optional Transmission Allison Combined Axle Weight Rating 60 . STINGER 70100 Boom T ruck Crane STI NGE R 7010 0 BOOM TRU CK CRA NE FEATURES 70 000 Ib 31 752 kg m aximum lifting capacity 110 33 5 3 m max imum she ave height

Related Books