69 2796EFS 01 UV2400U Air Purifier

69 2796efs 01 Uv2400u Air Purifier-Free PDF

  • Date:09 Nov 2020
  • Views:4
  • Downloads:0
  • Pages:72
  • Size:6.48 MB

Share Pdf : 69 2796efs 01 Uv2400u Air Purifier

Download and Preview : 69 2796efs 01 Uv2400u Air Purifier


Report CopyRight/DMCA Form For : 69 2796efs 01 Uv2400u Air Purifier


Transcription:

Before Installing this Product, Read these instructions carefully failure to follow them could damage the product and. cause a hazardous situation, Installer must be a trained experienced service technician. WARNING UV Light Hazard, Harmful to bare skin and eyes Can cause temporary or permanent loss of. vision Never look at lamps while illuminated, To prevent exposure to ultraviolet light disconnect power to the ultraviolet air. treatment system before servicing any part of the heating air conditioning system. View illumination only through lamp handle or sight glass. Do not attempt to bypass duct mount switch, Do not attempt to open housing unit is sealed to prevent ultraviolet light.
CAUTION Breakable Glass Hazard Can cause personal injury. Be careful when inserting lamp s into lamp base,Wear protective gloves when handling lamp s. CAUTION Personal Injury Hazard Power supply can cause electrical. Disconnect power supply before cleaning or replacing ultraviolet lamp s. Do not open base unit or lamp handle there are no user serviceable compo. nents inside, CAUTION UV Lamp Burn Hazard Harmful to bare skin Can cause severe. Disconnect power 15 minutes before removing ultraviolet lamp s. Parts Included,1 UV lamp handle,3 Foam Gasket,4 16W UV lamp 5. 5 AirBRIGHT Odor,Absorber included 4,in UV2400U5000. 6 Bushing 3,7 Sight Glass 6,8 Warning sticker 2,9 24 VAC Ballast 9.
10 Self Tapping 10,Screws 3 11,11 Power Cord,Typical Mounting Locations. We recommend the UV Air Purifier be installed on the supply side duct just above the. A coil but it can also be installed on the return side if necessary See Figures 1 and 2. The germicidal UV light should also be positioned to shine on the surfaces that are. prone to mold growth like the A coil or be placed in an open area of the return duct. where there are long straight runs, WARNING Do not mount device in location that allows ultraviolet light to be seen. after installation other than by the UV protected lamp handle or sight glass. Important Some materials inside the A coil including filter media flex duct wiring. etc may not be UV light resistant Cover materials affected by UV light with UV. shielding or reflective tape, The AirBRIGHT Odor Absorber unit should be oriented so that the air flows past the. UV Light first then into the AirBRIGHT Odor Absorber. FURNACE AIR HANDLER, Fig 1 Supply Side installation Airflow depicted by arrows. FURNACE AIR HANDLER, Fig 2 Return Side installation Airflow depicted by arrows.
Internal Mounting, Turn off main power source before installation Model information is. printed on the Power Unit cover, 1 Unfasten panel to gain access to mounting location. 2 Determine the optimal position for placement of the Air Purifier. 3 If necessary use a utility knife to cut the insulation on the inside of the duct. 4 Clean surface of glue dust etc, 5 Push the AirBRIGHT Odor Absorber into the base until it clicks into place. 6 Insert Snaplamp into base, 7 Rotate the lamp handle clockwise 8 Place the magnetic bars on the base. until it snaps in place directly on the clean metal surface. 9 Use foil tape to close the cut in the,insulation as needed.
10 Create a 5 8 0 625 in hole in the 12 Find a suitable location on the. duct and pass the cord through it Clip outside of the duct work near the. the bushing provided onto the cord at UV Lamp installation and apply the. a point close to the hole Plug the hole warning lamp replacement sticker. with the bushing 13 Drill a 1 2 in hole through the circle. on the sticker Press the UV sight,glass into hole,11 Secure access panel to the duct work. External Mounting for Metal Duct Applications, 1 Use the gasket to mark the duct openings Cut and remove openings making sure. to leave the metal between the holes intact,2 Push the AirBRIGHT Odor Absorber into. the base until it clicks into place, 3 Remove backing from the gasket and secure base to the duct. work using the foam gasket and self tapping screws M34687. 4 Insert lamp into base and turn handle clockwise to lock in place. Duct Board Mounting For Duct Board Applications Only. 1 Bend metal tabs of duct board adapter over the holes cut in the duct board. etc may not be UV light resistant Cover materials affected by UV light with UV shielding or reflective tape The AirBRIGHT Odor Absorber unit should be oriented so that the air flows past the UV Light first then into the AirBRIGHT Odor Absorber 6 Fig 1 Supply Side installation Airflow depicted by arrows M34597 FURNACE AIR HANDLER 7 Fig 2 Return Side installation Airflow depicted by

Related Books