2004 2005 QUEST REVISED SLIDING DOOR INITIALIZATION

2004 2005 Quest Revised Sliding Door Initialization-Free PDF

  • Date:31 Aug 2020
  • Views:7
  • Downloads:0
  • Pages:11
  • Size:493.91 KB

Share Pdf : 2004 2005 Quest Revised Sliding Door Initialization

Download and Preview : 2004 2005 Quest Revised Sliding Door Initialization


Report CopyRight/DMCA Form For : 2004 2005 Quest Revised Sliding Door Initialization


Transcription:

SLIDING DOOR INITIALIZATION PROCDURE, NOTE The following procedure is for one sliding door It must be repeated if needed on a. second door,1 Open the sliding door,2 Turn the ignition key ON. 3 Turn the Automatic Door Main Switch OFF,4 Within 3 seconds after step 3 press the. sliding door B pillar switch LH or RH,depending on which door you are. initializing 10 times within 10 seconds, 5 Within 3 seconds after step 4 turn the ignition key OFF ON.
You should hear three 3 sliding door warning chimes. The three chimes indicate the controller has entered initialization mode. Normal door functions are disabled during initialization. SIDE GUARD MOLDING,SIDE GUARD MOLDING PFP 76840,Removal and Installation EIS001VU. Never apply tack paper adhesive remover to body panel surface finished with lacquer based paints. Original side guard molding is affixed to body panel with double faced adhesive tape. 1 Heat molding to between 30 and 40 C 86 to 104 F with a heat gun. 2 Raise end of molding and cut away tape to remove molding Remove all traces of tape. 3 Remove LH rear combination lamp Refer to LT 124 REAR COMBINATION LAMP. 4 Remove screw from slide door rail cover,5 Open sliding door and release the front clip. 6 Close sliding door Carefully pull off slide door rail cover releasing clips so as not to deform body sheet. 7 Remove door sash cover,Remove screw from top of door sash cover. Pull bottom of door sash cover outward and pull up off hooks. INSTALLATION, On vehicles coated with Hard Clear Coat use double faced 3M adhesive tape Product No 4210 or equiv. alent after priming with 3M primer Product No N200 or C 100 or equivalent. The repair parts are also affixed with double faced adhesive tape. To re use existing molding clean all traces of double sided tape from the molding and apply new double. faced tape to the molding, 1 Clean the panel surface with isopropyl alcohol or equivalent to degrease the surface.
2 Heat the panel and molding tape surface to 30 to 40 C 86 to 104 F. 3 Remove the backing sheet from the tape surface, 4 Press ends by hand and use a roller to apply 5 kg f 11 lbs f to press molding to door surface. Revision January 2005 EI 26 2004 Quest,BODY SIDE TRIM. BODY SIDE TRIM PFP 76913,Removal and Installation EIS001VW. Wrap the tip of flat bladed screwdriver with a cloth when removing metal clips from finishers. When removing or installing body side welts do not allow butyl seal to come in contact with pillar. Revision January 2005 EI 30 2004 Quest,BODY SIDE TRIM. 1 Center pillar upper finisher LH 2 Center pillar lower finisher LH 3 Front door welt. 4 Front pillar finisher LH 5 Upper dash side finisher LH 6 Lower dash side finisher LH. 7 Front kicking plate 8 Trim clips 9 Center pillar lower escutcheon LH. 10 Rear finisher cover 11 Luggage side cup holder LH 12 Center finisher cover. 13 Rear center pillar finisher LH 14 Rear lower finisher assembly LH 15 Cargo net hooks. 16 Power point 17 Power point cap 18 Rear kick escutcheon LH. 19 Luggage side lower escutch 21 Power sliding door switch assem. 20 Luggage side panel LH C,eon LH bly, 22 Rear pillar upper finisher LH 23 Trim clips 24 Rear kicking plate.
25 Assist grip end caps 26 Center pillar assist grip 27 Back door open close switch. 28 Sliding door welt 29 Center pillar upper cover 30 Sliding door drip weatherstrip LH D. Revision January 2005 EI 31 2004 Quest,BODY SIDE TRIM. RIGHT SIDE AND REAR, Wrap the tip of flat bladed screwdriver with a cloth when removing metal clips from garnishes. When removing or installing body side welts do not allow butyl seal to come in contact with pillar. 1 Roof finisher 2 Luggage room lamp 3 Cargo net, 4 Back door upper finisher 5 Back door lower finisher 6 Back door mask. Revision January 2005 EI 32 2004 Quest,BODY SIDE TRIM. 7 Back door welt 8 Back door pull handle 9 Pull handle covers RH LH. 10 Back door bumpers 11 Gas leak check lid 12 Cargo net hooks A. 13 Luggage side lower escutcheon RH 14 Rear kick escutcheon RH 15 Rear lower finisher assembly RH. 16 Rear pillar cover RH 17 Cup holder luggage side RH 18 Center pillar cover RH. 19 Rear center pillar finisher RH 20 Rear pillar upper finisher RH B. CENTER PILLAR LOWER FINISHER,Removal and Installation C.
1 Remove seat belt anchor Refer to SB 4 Removal and Installation of Front Seat Belt. 2 Remove front and rear kicking plates,3 Remove center pillar lower finisher D. Disconnect harness to back door opener switch,Installation is in the reverse order of removal. CENTER PILLAR UPPER FINISHER,Removal and Installation. 1 Remove seat belt shoulder anchor and D ring Refer to SB 4 Removal and Installation of Front Seat F. 2 Remove front and rear kicking plates,3 Remove center pillar lower finisher G. 4 Remove cover and screws,5 Remove center pillar upper finisher.
Installation is in the reverse order of removal H,REAR CENTER PILLAR FINISHER. Removal and Installation,1 Remove rear kicking plate. 2 Remove rear kick escutcheon, 3 Remove rear lower finisher assembly Refer to EI 34 REAR LOWER FINISHER ASSEMBLY J. 4 Remove cover and screws from rear center pillar finisher. 5 Remove rear center pillar finisher,Installation is in the reverse order of removal K. DASH SIDE FINISHER,Removal and Installation,1 Remove front kicking plate.
2 Remove upper dash side finisher,3 Remove lower dash side finisher M. Insert screw driver rolled with cloth between panel on vehicle. and clip as indicated with arrow and disconnect clip. Installation is in the reverse order of removal,FRONT PILLAR FINISHER. Removal and Installation, 1 Remove defrost grille assembly Refer to IP 10 INSTRUMENT PANEL ASSEMBLY. 2 Remove upper dash side finisher,3 Remove front pillar finisher. Installation is in the reverse order of removal,Revision January 2005 EI 33 2004 Quest.
Classification Reference Date,EL09 041a NTB09 113a February 16 2010. 2004 2007 QUEST SLIDING DOOR MOTOR AND CABLE,ASSEMBLY REPLACEMENT. This bulletin has been amended The Service Procedure has been revised No other changes have been made. Please discard previous copies of this bulletin,APPLIED VEHICLES 2004 2007 Quest V42. IF YOU CONFIRM, You need to replace the sliding door motor or cable closure assembly for any reason. As needed for the repair replace only the motor or only the cable assembly with the part. listed in the Parts Information section, NOTE These parts are now available separately Do not replace the entire assembly when.
only the motor or only the cable assembly is needed. PARTS INFORMATION,DESCRIPTION PART QUANTITY,Motor Assy RR Door PSD LH 82731 5Z000 1 if needed. Closure Assy Slide Door LH 82511 5Z00A 1 if needed. Motor Assy RR Door PSD RH 82730 5Z000 1 if needed, Closure Assy Slide Door RH 82510 5Z00A 1 if needed. IMPORTANT The purpose of ACTION above is to give you a quick idea of the work. you will be performing You MUST closely follow the entire Service Procedure as it contains. information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians not do it yourselfers Qualified technicians are. properly trained individuals who have the equipment tools safety instruction and know how to do a job. properly and safely NOTE If you believe that a described condition may apply to a particular vehicle DO. NOT assume that it does See your Nissan dealer to determine if this applies to your vehicle. CLAIMS INFORMATION, Submit a Primary Failed Part PP line claim using the following claims coding. DESCRIPTION PFP OP CODE SYM DIA FRT,RPL Sliding Door Motor 1 UL31AA ZE 32 2. 1 Refer to the electronic parts catalog FAST or equivalent and use the appropriate Slide. Door Closure Motor Right or Left Side part number as the Primary Failed Part PFP. 2 Reference the current Nissan Warranty Flat Rate Manual and use the indicated flat rate. SERVICE PROCEDURE,1 Remove the sliding door motor and.
cable assembly,Refer to the BL section in the,applicable Electronic Service. Manual ESM for Cable assembly,removal installation instructions. 2 Remove the motor from the cable,3 As needed for the repair replace the. motor or cable assembly with the,part listed in the Parts Information. 4 Pull the two ends of the cable to,ensure the cable is not tangled.
inside the drum housing,5 Confirm the bushing is in the. location shown in Figure 2 Bushing,2 3 NTB09 113a,Tension pulleys. in park position,6 Confirm both tension pulleys j hooks. are in the park position,7 Install the motor onto the cable. Torque the motor mounting bolts,3 8 4 5 N m 0 39 0 46 kg m.
34 40 in lb Motor,Motor mounting bolts,Move tension pulleys. to active position,8 Move the tension pulleys to the active. un park position,9 Reinstall the remaining parts in the. reverse order of removal,3 3 NTB09 113a,6 Turn the Automatic Door Main Switch ON. 7 Press and hold the driver s overhead Sliding,Door Open Close Switch LH or RH.
depending on which door you are initializing,until the sliding door completely closes and. stops then release the switch, 8 Press and hold the same sliding door switch again until the door completely opens and. stops then release the switch Same switch as step 7. 9 Press and hold the same switch again until the door completely closes and stops then. release the switch Same switch as step 7 and 8, 10 Turn the ignition key OFF One sliding door is now initialized. The initialized door will now operate normally, If needed repeat steps 1 through 10 for a second sliding door. 2004 2007 QUEST SLIDING DOOR MOTOR AND CABLE ASSEMBLY REPLACEMENT APPLIED VEHICLES 2004 2007 Quest V42 IF YOU CONFIRM You need to replace the sliding door motor or cable closure assembly for any reason ACTION As needed for the repair replace only the motor or only the cable assembly with the part listed in the Parts Information section

Related Books